/Shell/Bash/3.4.5 packet tracer configure trunks

3.4.5 packet tracer configure trunks

S3(config)#interface g0/2
S3(config-if)#switchport mode trunk
S3(config-if)#switchport trunk native vlan 99

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S2#show interface g0/1 switchport
Name: Gig0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 99 (Native)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: All
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S1#show vlan brief

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4
                                                Fa0/5, Fa0/6, Fa0/7, Fa0/8
                                                Fa0/9, Fa0/10, Fa0/11, Fa0/12
                                                Fa0/13, Fa0/14, Fa0/15, Fa0/16
                                                Fa0/17, Fa0/18, Fa0/19, Fa0/20
                                                Fa0/21, Fa0/22, Fa0/23, Fa0/24
                                                Gig0/1, Gig0/2
10   Faculty/Staff                    active    
20   Students                         active    
30   Guest(Default)                   active    
88   Management                       active    
99   Native                           active    
1002 fddi-default                     active    
1003 token-ring-default               active    
1004 fddinet-default                  active    
1005 trnet-default                    active

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet0/2 (99), with S3 GigabitEthernet0/2 (1).
%CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on GigabitEthernet0/1 (99), with S2 GigabitEthernet0/1 (1).

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S3#show interface g0/2 switchport
Name: Gig0/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 99 (Native)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: All
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S1(config)# interface range g0/1 - 2
S1(config-if)# switchport mode trunk

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S2(config)#interface g0/1
S2(config-if)#switchport mode trunk
S2(config-if)#switchport trunk native vlan 99

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S3#show vlan brief

VLAN Name                             Status    Ports
---- -------------------------------- --------- -------------------------------
1    default                          active    Fa0/1, Fa0/2, Fa0/3, Fa0/4
                                                Fa0/5, Fa0/7, Fa0/8, Fa0/9
                                                Fa0/10, Fa0/12, Fa0/13, Fa0/14
                                                Fa0/15, Fa0/16, Fa0/17, Fa0/19
                                                Fa0/20, Fa0/21, Fa0/22, Fa0/23
                                                Fa0/24, Gig0/1, Gig0/2
10   Faculty/Staff                    active    Fa0/11
20   Students                         active    Fa0/18
30   Guest(Default)                   active    Fa0/6
88   Management                       active    
99   Native                           active    
1002 fddi-default                     active    
1003 token-ring-default               active    
1004 fddinet-default                  active    
1005 trnet-default                    active

Source: itexamanswers.net

3.4.5 packet tracer configure trunks

S1(config-if)# switchport trunk native vlan 99

Source: itexamanswers.net

Similar codes

4 votes310 views1 answer
Laravel sail install php extensions
Shell/Bash
0 vote329 views1 answer
Thelinuxterminal.com install nvm
Shell/Bash
1 vote318 views2 answers
Crear usuario linux
Shell/Bash
27 votes334 views3 answers
Ubuntu check available packages
Shell/Bash
-1 vote280 views1 answer
Su - postgres
Shell/Bash
0 vote326 views1 answer
Failed at the [email protected] install script
Shell/Bash
2 votes331 views1 answer
Install idle3 terminal
Shell/Bash
0 vote322 views1 answer
Redirect folder to 403
Shell/Bash
0 vote314 views1 answer
How to start xammp on linux
Shell/Bash
1 vote344 views1 answer
How to install ssh in windows 10
Shell/Bash